Advantech AMAX-4850

SPHINX i Europa
DK
  • AT
  • BE
  • DK
  • FR
  • DE
  • IE
  • IT
  • NL
  • ES
  • SE
  • CH
  • UK
Produktgrupper > I/O Modules > Advantech AMAX-4850

Advantech AMAX-4850

16-ch IDI & 8-ch PhotoMOS EtherCAT Remote I/O module

Advantech AMAX-4850
5174_27295.png
5174_27296.png
5174_27297.png
  • egenskaberegenskaber
  • beskrivelsebeskrivelse
  • yderligere informationyderligere information
  • PDFPDF
  • Suitable for EtherCAT networks
  • 16-ch digital input and 8-ch PhotoMOS Relay output (Form A)
  • 1500 VDC optical isolation for relay outputs
  • Quick removable European type connector
  • LED indicators for I/O status
  • Supports EtherCAT Distributed Clock (DC) mode and SyncManager mode
  • Two Rotary switches for up to 256 slave IDs
The AMAX-4850 is an industrial EtherCAT slave module equipped with the EtherCAT protocol. Its compact size and DIN-rail mount kit can install easily in a cabinet. Euro type pluggable terminal blocks and LED indicator help users to maintain and set up their system. All digital input and PhotoMOS Relay Output channels are protected by isolation circuits.


Compact Size

High density channel count in a compact design helps increase space utilization ratio. Din-rail mounting kit ensures easy installation in cabinets.


Easy to Maintain

Terminal block, LED indicator, Switch and EtherCAT port can be operated at front side. These provide a convenient way to wire, test, debug or maintain. In particular, AMAX-4800 series equip euro type pluggable terminal block to insert wires without screw tools. These features can help user to reduce maintenance cost and time.


Good expandability

Since a total of 65,535 nodes per network segment can be connected, the I/O channel amount will not be limited by PCI/PCIE slot any more. The physics of Ethernet allow a cable length of up to 100 m (300 ft) between two nodes, so expensive signal cable will be replaced. This means less IPC, simpler wiring topology and lower cost.


Synchronization

The synchronization time between each slave module is one of important parameter for motion control. AMAX-4800 series support EtherCAT distributed Clock. By using distributed clocks , modules can calibrate the time difference less than 1 us to output synchronize signal.
ProdGrafik

Communication

    Interface
    EtherCAT

    Data transfer medium
    Ethernet/EtherCAT cable (min. CAT 5), shielded

    Distance between modules
    Max. 100 m (100BASE-TX)

    Communication Cycle Time
    200us

    Data transfer rates
    100 Mbps

    Configuration
    Not required



Digital Input

    Channels
    16

    Input voltage
    Logic 0: 3 V max.; Logic 1: 10 V min. (30 V max.)

    Isolation protection
    2,500 V DC



PhotoMOS Relay Output

    Channels
    8

    Relay type
    PhotoMOS SPST(Form A)

    Load Voltage
    60V (AC peak or DC)

    Load current
    1.2A

    Peak load current
    4A @100ms(1 pulse)

    Isolation protection
    1,500 V DC

    Turn-on time
    1 ms typical

    Turn-off time
    0.6 ms typical



General

    Connectors
    10-pin 3.81 mm terminal block * 4 (I/O)
    3-pin 3.81 mm screw terminal block (power) RJ-45 * 2 (EtherCAT)

    Dimensions
    120 mm x 120 mm x 40 mm

    Operating temperature
    -20 ~ 60°C (32 ~ 140°F)

    Storage temperature
    -40 ~ 70°C (-40 ~ 158°F)

    Storage humidity
    5 ~ 95% RH (non-condensing)

    Power supply
    10 ~ 30 V DC

    Power Consumption
    Typical 85mA @24V; Max. 110mA @24V



Ordering Information


      AMAX-4850-AE

          16 IDI & 8 PhotoMOS EtherCAT Remote I/O module



      96PS-A40WDIN

          DIN RAIL A/D 100-240V 40W 24V


Kunder, der kiggede på dette produkt, kiggede også på
Accept all Reject Configure

This website uses cookies to provide the best possible experience. More information.