Advantech AMAX-4860

SPHINX i Europa
DK
  • AT
  • BE
  • DK
  • FR
  • DE
  • IE
  • IT
  • NL
  • ES
  • SE
  • CH
  • UK
Produktgrupper > I/O Modules > Advantech AMAX-4860

Advantech AMAX-4860

8-ch IDI & 8-ch Relay EtherCAT Remote I/O module

Advantech AMAX-4860
5175_14401.png
5175_12075.png
  • egenskaberegenskaber
  • beskrivelsebeskrivelse
  • yderligere informationyderligere information
  • PDFPDF
  • Suitable for EtherCAT networks
  • 8-ch Isolated Digital Input and 8-ch Form A-type Relay Output
  • High-voltage isolation on input channel (2,500 VDC)
  • Quick removable European type connector
  • LED indicators for I/O status
  • Supports EtherCAT Distributed Clock (DC) mode and SyncManager mode
  • Two Rotary switches for up to 256 slave IDs
The AMAX-4860 is an industrial EtherCAT slave module equipped with the EtherCAT protocol. Its compact size and DIN-rail mount kit can install easily in a cabinet. Euro type pluggable terminal blocks and LED indicator help users to maintain and set up their system. All digital input channels are protected by 2,500 VDC isolation circuits.


Compact Size

High density channel count in a compact design helps increase space utilization ratio. Din-rail mounting kit ensures easy installation in cabinets.


Easy to Maintain

Terminal block, LED indicator, Switch and EtherCAT port can be operated at front side. These provide a convenient way to wire, test, debug or maintain. In particular, AMAX-4800 series equip euro type pluggable terminal block to insert wires without screw tools. These features can help user to reduce maintenance cost and time.


Good expandability

Since a total of 65,535 nodes per network segment can be connected, the I/O channel amount will not be limited by PCI/PCIE slot any more. The physics of Ethernet allow a cable length of up to 100 m (300 ft) between two nodes, so expensive signal cable will be replaced. This means less IPC, simpler wiring topology and lower cost.


Synchronization

The synchronization time between each slave module is one of important parameter for motion control. AMAX-4800 series support EtherCAT distributed Clock. By using distributed clocks , modules can calibrate the time difference less than 1 us to output synchronize signal.
ProdGrafik

Communication

    Interfac
    EtherCAT

    Data transfer medium
    Ethernet/EtherCAT cable (min. CAT 5), shielded

    Distance between modules
    Max. 100 m (100BASE-TX)

    Data transfer rates
    100 Mbps

    Configuration
    Not required

    Communication Cycle Time
    200us



Digital Input

    Channels
    8

    Input voltage
    Logic 0: 3 V max.; Logic 1: 10 V min. (30 V max.)

    Isolation protection
    2,500 V DC



Relay Output

    Channels
    8
    Relay Type
    Form A

    Contact Rating (resistive)
    2A@250V AC , 2A@30V DC

    Max. Switching Power
    500VA , 60W

    Max. Switching Voltage
    270V AC , 125V DC

    Resistance
    30m Ω max.

    Operating Time
    Max. 10ms

    Releasing Time
    Max. 5ms

    Life Expectancy
    Mechanical 2 x 10 7 ops. at no load.
    Electrical 3 x 10 4 ops. @2A/250V AC



General

    Connectors
    10-pin 3.81 mm terminal block * 3 (I/O)
    3-pin 3.81 mm screw terminal block (power) RJ-45 * 2 (EtherCAT)

    Dimensions
    120 mm x 120 mm x 40 mm

    Operating temperature
    -20 ~ 60°C (32 ~ 140°F)

    Storage temperature
    -40 ~ 70°C (-40 ~ 158°F)

    Storage humidity
    5 ~ 95% RH (non-condensing)

    Power supply
    10 ~ 30 V DC

    Power Consumption
    Typical 85mA @24V; Max. 110mA @24V





Ordering Information


      AMAX-4860-AE

          8-ch IDI & 8-ch Relay EtherCAT Remote I/O module






      96PS-A40WDIN

          DIN RAIL A/D 100-240V 40W 24V

Kunder, der kiggede på dette produkt, kiggede også på
Accept all Reject Configure

This website uses cookies to provide the best possible experience. More information.