Advantech AMAX-4830

SPHINX i Europa
DK
  • AT
  • BE
  • DK
  • FR
  • DE
  • IE
  • IT
  • NL
  • ES
  • SE
  • CH
  • UK
Produktgrupper > I/O Modules > Advantech AMAX-4830

Advantech AMAX-4830

16-ch Isolated Digital Input and 16-ch Isolated Digital Output EtherCAT Remote I/O Module

Advantech AMAX-4830
5176_12076.png
5176_12077.png
  • egenskaberegenskaber
  • beskrivelsebeskrivelse
  • yderligere informationyderligere information
  • PDFPDF
  • Suitable for EtherCAT networks
  • 16-ch digital input and 16-ch digital output with 2,500 VDC isolation
  • Wide input voltage range (10 ~ 30 VDC)
  • Wide output voltage range (5 ~ 40 VDC) and high output current (350 mA/ch)
  • Quick removable European type connector
  • LED indicators for I/O status
  • Supports EtherCAT Distributed Clock (DC) mode and SyncManager mode
  • Two Rotary switches for up to 256 slave IDs
The AMAX-4830 is an industrial EtherCAT slave module equipped with the EtherCAT protocol. Its compact size and DIN-rail mount kit can install easily in a cabinet. Euro type pluggable terminal blocks and LED indicator help users to maintain and set up their system. All digital input and digital output channels are protected by 2,500 V DC isolation.


Compact Size

High density channel count in a compact design helps increase space utilization ratio. Din-rail mounting kit ensures easy installation in cabinets.


Easy to Maintain

Terminal block, LED indicator, Switch and EtherCAT port can be operated at front side. These provide a convenient way to wire, test, debug or maintain. In particular, AMAX-4800 series equip euro type pluggable terminal block to insert wires without screw tools. These features can help user to reduce maintenance cost and time.


Good expandability

Since a total of 65,535 nodes per network segment can be connected, the I/O channel amount will not be limited by PCI/PCIE slot any more. The physics of Ethernet allow a cable length of up to 100 m (300 ft) between two nodes, so expensive signal cable will be replaced. This means less IPC, simpler wiring topology and lower cost.


Synchronization

The synchronization time between each slave module is one of important parameter for motion control. AMAX-4800 series support EtherCAT distributed Clock. By using distributed clocks , modules can calibrate the time difference less than 1 us to output synchronize signal.
ProdGrafik
Communication

    Interface
    EtherCAT

    Data transfer medium
    Ethernet/EtherCAT cable (min. CAT 5), shielded

    Distance between modules
    Max. 100 m (100BASE-TX)

    Communication Cycle Time
    200us

    Data transfer rates
    100 Mbps

    Configuration
    Not required



Digital Input

    Channels
    16

    Input voltage
    Logic 0: 3 V max.
    Logic 1: 10 V min. (30 V max.)

    Isolation protection
    2,500 V DC



Digital Output

    Channels
    16

    Load voltage
    5 ~ 40 V DC

    Load current
    350mA/ch (sink) @ 25°C
    250mA/ch (sink) @ 60°C

    Isolation protection
    2,500 V DC

    Opto-isolator Response Time
    100us



General

    Connectors
    10-pin 3.81 mm terminal block * 4 (I/O)
    3-pin 3.81 mm screw terminal block (power) RJ-45 * 2 (EtherCAT)

    Dimensions
    120 mm x 120 mm x 40 mm

    Operating temperature
    -20 ~ 60°C (32 ~ 140°F)

    Storage temperature
    -40 ~ 70°C (-40 ~ 158°F)

    Storage humidity
    5 ~ 95% RH (non-condensing)

    Power supply
    10 ~ 30 V DC

    Power Consumption
    Typical 85mA @24V;
    Max. 110mA @24V




Ordering Information


      AMAX-4830-AE

          16-ch isolated digital input and 16-ch isolated digital output EtherCAT remote I/O module



      96PS-A40WDIN

          DIN RAIL A/D 100-240V 40W 24V

Kunder, der kiggede på dette produkt, kiggede også på
Accept all Reject Configure

This website uses cookies to provide the best possible experience. More information.