Advantech BB-MDR-40 Series

Model MDR-40 is an industrial single-phase, low-profile, low cost power supply suitable for installations where space is at a premium - ideal for control panels and other industrial, control and automation applications. This switched-mode unit features a wide operating temperature range, finger-safe terminals and protection from short-circuit, overload and over-voltage. The power supply is adaptable to TS-35 / 7.5 or 15 DIN mount installation.

SPECIFICATIONS

MODEL	BB-MDR-40-5	BB-MDR-40-12	BB-MDR-40-15	BB-MDR-40-24
OUTPUT
DC VOLTAGE	5V	12V	15V	24V
RATED CURRENT	6A	3.33A	1.7A	0.83A
CURRENT RANGE	0 ~ 6A	0 ~ 3.33A	0 ~ 1.7A	0 ~ 0.83A
RATED POWER	30W	40W	40.8W	39.8W
RIPPLE & NOISE (max.) Note.2	80mVp-p	120mVp-p	150mVp-p	200mVp-p
VOLTAGE ADJ. RANGE	5 ~ 6V	12 ~ 15V	24 ~ 30V	48 ~ 56V
VOLTAGE TOLERANCE    Note.3	± 2.0%	± 1.0%	± 1.0%	± 1.0%
LINE REGULATION	± 1.0%	± 1.0%	± 1.0%	± 1.0%
LOAD REGULATION	± 1.0%	± 1.0%	± 1.0%	± 1.0%
SETUP, RISE TIME     Note.5	500ms, 30ms/230VAC     500ms, 30ms/115VAC at full load
HOLD UP TIME (Typ.)	50ms/230VAC      20ms/115VAC at full load
INPUT
VOLTAGE RANGE   Note.6	85 ~ 264VAC       120 ~ 370VDC
FREQUENCY RANGE	47 ~ 63Hz
EFFICIENCY (Typ.)	78%	86%	88%	88%
AC CURRENT (Typ.)	1.1A/115VAC      0.7A/230VAC
INRUSH CURRENT (Typ.)	COLD START 30A/115VAC      60A/230VAC
LEAKAGE CURRENT (Typ.)	<1mA / 240VAC
PROTECTION
OVERLOAD	Above 105% rated output power
	Protection type : Constant current limiting, recovers automatically after fault condition is removed
OVER VOLTAGE	6.25 ~ 7.25V	15.6 ~ 18V	31.2 ~ 36V	31.2 ~ 36V
	Protection type : Shut down o/p voltage, re-power on to recover
FUNCTION
DC OK ACTIVE SIGNAL	Relay contact rating(max.): 30V/1A resistive
ENVIRONMENT
WORKING TEMP.	-20 ~ +70 °C (Refer to "Derating Curve")
WORKING HUMIDITY	20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY	-40 ~ +85 °C, 10 ~ 95% RH
TEMP. COEFFICIENT	± 0.03%/ °C °C (0 ~ 50)
VIBRATION	Component : 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes ; Mounting : Compliance to IEC60068-2-6
SAFETY &EMC (Note 4)
SAFETY STANDARDS	UL508, UL69050-1, TUV EN60950-1. Class I, Div. 2 Group A, B, C, D Hazardous Locations T4 approved
WITHSTAND VOLTAGE	I/P-O/P:3KVAC       I/P-FG:2KVAC      O/P-FG:0.5KVAC
ISOLATION RESISTANCE	I/P-O/P,   I/P-FG,   O/P-FG:>100M Ohms / 500VDC / 25°C/ 70% RH
EMC EMISSION	Compliance to EN55011, EN55032 (CISPR32), EN61204-3 Class B, EN61000-3-2,-3
EMC IMMUNITY	Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A
OTHERS
MTBF	301.7K hrs min.      MIL-HDBK-217F (25°C)
DIMENSION	40*90*100mm (W*H*D)
PACKING	0.3Kg;    42pcs/13.6Kg/0.82CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 °C of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” 5. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.

Ordering Information

Available Modules
BB-MDR-40-5	30W, 5VDC, 6A, AC-DC Single Output DIN Power Supply, Slim Plastic Case
BB-MDR-40-12	40W, 12VDC, 3.33A, AC-DC Single Output DIN Power Supply, Slim Plastic Case
BB-MDR-40-15	40.8W, 24VDC, 1.7A, AC-DC Single Output DIN Power Supply, Slim Plastic Case
BB-MDR-40-24	39.8W, 48VDC, 0.83A, AC-DC Single Output DIN Power Supply, Slim Plastic Case